[1]邵旭东,李玉祺,廖子南,等.UHPC华夫桥面板抗弯性能试验及有限元分析[J].长安大学学报(自然科学版),2018,38(03):52-63.
　SHAO Xu dong,LI Yu qi,LIAO Zi nan,et al.Test and finite element analysis on bending performance of UHPC Waffle deck panel[J].Journal of Chang’an University (Natural Science Edition),2018,38(03):52-63.
点击复制

UHPC华夫桥面板抗弯性能试验及有限元分析()
分享到：

长安大学学报（自然科学版）[ISSN:1006-6977/CN:61-1281/TN]

卷:
第38卷
期数:
2018年03期
页码:
52-63
栏目:
桥梁与隧道工程
出版日期:
2018-05-31

文章信息/Info

Title:
Test and finite element analysis on bending performance of UHPC Waffle deck panel
作者:
邵旭东; 李玉祺; 廖子南; 曹君辉
(1. 湖南大学 土木工程学院，湖南 长沙 410082； 2. 长沙市规划设计院有限责任公司，湖南 长沙 410007)
Author(s):
SHAO Xudong;  LI Yuqi;  LIAO Zinan;  CAO Junhui
（1. School of Civil Engineering, Hunan University, Changsha 410082, Hunan, China； 2. Changsha Planning & Design Institute Co., Ltd., Changsha 410007, Hunan, China）
关键词:
桥梁工程; 华夫桥面板; 抗弯静力试验; 有限元模拟; 参数分析
Keywords:
bridge engineering;  Waffle deck panel;  static bending test;  finite element simulation;  parametric analysis
文献标志码:
A
摘要:
为研究超高性能混凝土（UHPC）华夫桥面板的横桥向抗弯性能，首先开展了4个横肋的足尺条带模型抗弯性能静力试验；然后采用ABAQUS有限元软件建立了试件非线性有限元模型，模型中考虑了材料非线性和几何非线性，其中对UHPC考虑了混凝土损伤塑性模型等，并利用该有限元模型模拟试验全过程；最后通过有限元参数分析明确主要设计参数对UHPC华夫桥面板横向抗弯性能的影响规律，包括横肋纵向配筋率（钢筋直径）、横肋高度、顶板高度以及横肋间距等。研究结果表明：正弯矩作用下试件的受弯破坏过程包含线弹性阶段、裂缝开展阶段和屈服阶段；华夫桥面板横肋底面出现横向裂缝导致结构刚度第1次下降，随着裂缝的发展，截面内力重分布使得底部纵筋应力持续增大直至屈服，导致刚度出现第2次下降，裂缝进一步向上开展逼近翼缘板顶部，由于受拉区充分发展导致顶板纵筋受拉屈服，刚度出现第3次下降，结构刚度严重衰减，试件承载力接近极限，趋于破坏；有限元计算结果与试验结果吻合良好；通过参数分析发现，增加纵筋配筋率（钢筋直径）对初裂荷载影响很小，但可有效限制裂缝的发展；增加肋高对初裂荷载有一定的提高作用，还可提高矮肋T梁的初始刚度、开裂后刚度以及极限承载力；增加顶板高度也可起到同样的效果，但肋高对初始刚度的提高效率是顶板的5.4倍；增加横肋间距可提高单根横肋的初始刚度、开裂后刚度以及极限承载力，但削弱了横向整体刚度。
Abstract:
In order to study the transversal bending performance of UHPC Waffle deck panel, four specimens with transverse rib in full scale were firstly carried out for bending performance static test. Then nonlinear finite element models of specimens were established by using the finite element software ABAQUS, in which the material nonlinearity, geometric nonlinearity and plastic damage model of concrete for UHPC were considered, and the whole test process was simulated by using the finite element model. Finally, the influence of primary parameters on the transversal bending performance of UHPC Waffle deck panel was ascertained by parameter analysis, which included the longitudinal reinforcement ratio of transverse rib (the diameter of reinforcement), the height of transverse rib, the height of top plane and the spacing of transverse rib. The results show that specimens undergo following typical stages under the action of positive bending moment, linear elastic stage, crackdeveloping stage and yield stage. Transversal cracks appear at the bottom of transverse rib, which lead to the first decrease of structural stiffness. With the development of cracks, the redistribution of internal forces results in a continuous rise of stress in the reinforcement until its yielding, which causes a second drop of stiffness. Then cracks propagates further upward to the bottom of flange, because the tensile zone develops to the extreme point leading the upper reinforcement to yield, the stiffness of specimen decreases rapidly, which is the third decline of stiffness. The bearing capacity of specimen is close to the extreme and tends to be destroyed. The finite element results are consistent with those from experiments. Parameter analysis shows that the influence of the longitudinal reinforcement ratio (the diameter of reinforcement) on the initial cracking load is negligible, whereas the development of cracks can be restricted effectively. The increase of rib height can not only show some inhibitory effect on the initial cracking load, but also can enhance the initial stiffness, the stiffness after cracking and the ultimate bearing capacity of Tbeam. Increasing the height of top plane could also achieve a similar effect, but improvement efficiency of initial stiffness by increasing the rib height is 5.4 times of that by increasing the top plane height. The increase of rib spacing can improve initial stiffness, the stiffness after cracking as well as ultimate bearing capacity of a single transversal rib, but the global stiffness in transversal direction is impaired. 8 tabs, 19 figs, 26 refs.

相似文献/References:

[1]李宇,朱晞,杨庆山,等.高墩大跨桥梁结构的脆弱性分析[J].长安大学学报(自然科学版),2012,32(01):0.
[2]高亮,刘健新,张丹,等.桁架桥主梁三分力系数试验[J].长安大学学报(自然科学版),2012,32(01):0.
[3]刘旭政,王丰平,黄平明,等.斜拉桥各构件校验系数的常值范围[J].长安大学学报(自然科学版),2012,32(01):0.
[4]尚维波,张春宁.高墩刚构桥系梁抗震分析[J].长安大学学报(自然科学版),2012,32(01):0.
[5]邬晓光,李冀弘,宋伟伟.基于改进响应面法的在役PC桥梁承载力可靠性[J].长安大学学报(自然科学版),2012,32(03):53.
　WU Xiao-guang,LI Ji-hong,SONG Wei-wei.Reliability of existing PC bridge based on improved response surface method[J].Journal of Chang’an University (Natural Science Edition),2012,32(03):53.
[6]石雄伟,袁卓亚,马毓泉,等.钢板-混凝土组合加固预应力混凝土箱梁[J].长安大学学报(自然科学版),2012,32(03):58.
　SHI Xiong-wei,YUAN Zhuo-ya,MA Yu-quan,et al.Prestressed concrete box girder strengthened with comsposition of steel plate and concrete[J].Journal of Chang’an University (Natural Science Edition),2012,32(03):58.
[7]李传习,陶 伟,董创文.斜交墩截面刚度与弯曲正应力[J].长安大学学报(自然科学版),2012,32(03):63.
　LI Chuan-xi,TAO Wei,DONG Chuang-wen.Sectional stiffness and bending normal stress of oblique pier[J].Journal of Chang’an University (Natural Science Edition),2012,32(03):63.
[8]邓继华,邵旭东.带铰平面梁元几何非线性有限元分析[J].长安大学学报(自然科学版),2012,32(03):68.
　DENG Ji-hua,SHAO Xu-dong.Geometric nonlinear finite element analysis of plane beam element with hinge[J].Journal of Chang’an University (Natural Science Edition),2012,32(03):68.
[9]蒲广宁,赵 煜,宋一凡.减梁增肋法加固空心板桥的力学性能[J].长安大学学报(自然科学版),2012,32(06):38.
　PU Guang-ning,ZHAO Yu,SONG Yi-fan.Mechanical properties of strengthening hollow slab bridge based on beam-reduction and rib-addition method[J].Journal of Chang’an University (Natural Science Edition),2012,32(03):38.
[10]党 栋,贺拴海,周勇军,等.基于车辆统计数据的汽车荷载标准值取值与评估[J].长安大学学报(自然科学版),2012,32(06):44.
　DANG Dong,HE Shuan-hai,ZHOU Yong-jun,et al.Choosing and assessment for the standard of vehicle load based on vehicle statistical data[J].Journal of Chang’an University (Natural Science Edition),2012,32(03):44.

更新日期/Last Update: 2018-06-13