[1]张泽宇,卜正锋,惠记庄,等.牵引工况下大功率液力变矩器总成热特性[J].长安大学学报(自然科学版),2018,38(03):116-126.
　ZHANG Ze yu,BU Zheng feng,HUI Ji zhuang,et al.Thermal characteristics of assembly of high power torqueconverter in traction condition[J].Journal of Chang’an University (Natural Science Edition),2018,38(03):116-126.
点击复制

牵引工况下大功率液力变矩器总成热特性()
分享到：

长安大学学报（自然科学版）[ISSN:1006-6977/CN:61-1281/TN]

卷:
第38卷
期数:
2018年03期
页码:
116-126
栏目:
汽车与机械工程
出版日期:
2018-05-31

文章信息/Info

Title:
Thermal characteristics of assembly of high power torqueconverter in traction condition
作者:
张泽宇; 卜正锋; 惠记庄; 张富强; 谷立臣
（1. 长安大学 公路养护装备国家工程实验室，陕西 西安 710064； 2. 陕西航天动力高科技股份有限公司，陕西 西安 710077； 3. 西安建筑科技大学 机电工程学院，陕西 西安 710055）
Author(s):
ZHANG Zeyu1;  BU Zhengfeng2;  HUI Jizhuang1;  ZHANG Fuqiang1;  GU Lichen1; 3
（1. National Engineering Laboratory for Highway Maintenance Equipment, Changan University, Xian 710064,Shaanxi, China; 2. Shaanxi Aerospace Power CO., LTD, Xian 710077, Shaanxi, China; 3. School of〖JP2〗Mechanical Electronic Engineering, Xian University of Architecture and Technology, Xian 710055, Shaanxi, China)
关键词:
机械工程; 热特性; 热平衡理论; 大功率液力变矩器; 推土机
文献标志码:
A
摘要:
针对推土机在往返工况下液力变矩器油温经常超工作范围问题，分析其液力变矩器内部油温与车辆工况的变化规律，并对液力变矩器液压供油系统进行温度调节与保护，开展牵引工况下大功率液力变矩器总成的热特性研究。以热平衡理论为基础，分析推导液力变矩器的能量损失、传递效率、热量的产生和散失与油温之间关系。利用液力变矩器总成的台架试验，测试了YJ380型大功率液力变矩器在牵引工况下的扭矩、转速、流量、油温等基本特性参数。以试验数据为基础，建立了140 kW柴油发动机与该大功率液力变矩器的数学模型，并对其共同工作的数学模型进行了分析；在发动机与液力变矩器功率匹配的基础上，通过计算液力变矩器的能量损失以及散热器的散热效率，得出液力变矩器在不同工况下的内部油温。针对液压系统由于泵排量不足导致的油温过高现象，搭建供油系统模型，通过对液压系统的流量调节优化了液力变矩器总成的热平衡特性，通过控制液力变矩器的闭锁离合器对系统进行了温度保护。最后，将试验结果与数值模拟结果进行了对比验证。研究结果表明：利用发动机与液力变矩器共同工作数学模型计算的油温与实测出口、入口油温均值的相对误差约为2%，验证了该数学模型的正确性；在液力变矩器供油系统基础上，建立了恒温控制及温度的自动保护方案，当油温为60 ℃~80 ℃，或100 ℃~120 ℃时，通过调节系统流量能保持温度恒定，当油温小于60 ℃或大于120 ℃时，通过闭解锁控制可以保证液力变矩器动力总成的可靠性。
Abstract:
In the roundtrip conditions, the oil temperature of the torque converter often exceeds the bulldozers working range, in order to study the variation principle of the oil temperature inside hydraulic torque converters, adjust and protect its hydraulic system, the study on thermal characteristics of the assembly of high power torque converter in traction condition was proposed. Based on the theory of thermal equilibrium, the relationship among energy loss, transmission efficiency, generation and dissipation of heat, and oil temperature was analyzed and deduced. The bench was used to test the characteristic parameters of torque, speed, flow rate and oil temperature of YJ380 highpower torque converter for bulldozers under traction condition. According to the experimental data, the mathematical models of 140 kW diesel engine and the torque converter were established, and the cooperating model was analyzed. Based on the power matching between the engine and the torque converter, the oil temperature at the different speed ratio was obtained by calculating the energy loss of the torque converter and the dissipation efficiency of the radiator. Aiming at the phenomenon that the excess oil temperature in the hydraulic, due to the insufficient displacement of the hydraulic system, an oil supply system model was set up. The thermal balance characteristic of the torque converter assembly was optimized by adjusting the flow rate of the hydraulic system, and the temperature of the system was protected by controlling the lockup clutch.Based on the comparison of the experimental data and the calculated results, the deviation was about 2%, which verified the correctness of the mathematical model. Based on the oil supply system of the torqueconverter, a thermostatic control and temperature automatic protection scheme was established. When the oil temperature was in the range of 60 ℃~80 ℃, or 100 ℃~120 ℃， the flow rate could be kept constant by adjusting the flow of the system. When the oil temperature was less than 120 ℃ or higher than 120 ℃, the hydraulic torque converter could be lockup to ensuring the reliability of the assembly. 1 tab, 19 figs, 27 refs.

相似文献/References:

[1]罗文军,罗天洪,甘信富,等.基于模糊-PI控制的沥青混凝土摊铺机行驶系统仿真[J].长安大学学报(自然科学版),2012,32(01):0.
[2]刘清涛,蔡宗琰,刘晓婷,等.面向工艺路线的废旧零部件可再制造性评价[J].长安大学学报(自然科学版),2012,32(03):105.
　LIU Qing-tao,CAI Zong-yan,LIU Xiao-ting,et al.Assessment on remanufacturability of waste parts for process route[J].Journal of Chang’an University (Natural Science Edition),2012,32(03):105.
[3]林 涛,刘 学,董忠红,等.大差速比平地机离合器接合过程[J].长安大学学报(自然科学版),2012,32(06):100.
　LIN Tao,LIU Xue,DONG Zhong-hong,et al.Engagement process of motor graders big differential speed ratio clutch[J].Journal of Chang’an University (Natural Science Edition),2012,32(03):100.
[4]刘 钊,焦生杰.工程机械用发动机动力性能评价指标[J].长安大学学报(自然科学版),2012,32(06):106.
　LIU Zhao,JIAO Sheng-jie.Evaluation criterion of engine power properties for construction machinery[J].Journal of Chang’an University (Natural Science Edition),2012,32(03):106.
[5]孟彩茹,李 磊,赵 真,等.沥青搅拌设备振动筛筛箱的动态特性分析[J].长安大学学报(自然科学版),2012,32(02):101.
　MENG Cai-ru,LI Lei,ZHAO Zhen,et al.Dynamic performance analysis of vibrating screen box in asphalt mixer[J].Journal of Chang’an University (Natural Science Edition),2012,32(03):101.
[6]侯劲汝,沈建军,徐 倩.双钢轮振动压路机振幅不均匀性的分析[J].长安大学学报(自然科学版),2010,30(01):100.
　HOU Jing-ru,SHEN Jian-jun,XU Qian.Analysis on uneven amplitude of tandem vibratory roller[J].Journal of Chang’an University (Natural Science Edition),2010,30(03):100.
[7]赵铁栓,焦生杰,叶 敏.振动压路机无级调幅H_2/H_∞控制[J].长安大学学报(自然科学版),2010,30(03):87.
　ZHAO Tie-shuan,JIAO Sheng-gjie,YE Min.H2/H∞ control for stepless amplitude modulation of vibratory roller[J].Journal of Chang’an University (Natural Science Edition),2010,30(03):87.
[8]焦生杰,卡玛尔,林 涛,等.H型液压滤波器的合理应用[J].长安大学学报(自然科学版),2010,30(04):97.
　JIAO Sheng-jie,KAMAL Washahi,LIN Tao,et al.Reasonable application on H type hydraulic filter[J].Journal of Chang’an University (Natural Science Edition),2010,30(03):97.
[9]夏毅敏,薛 静,周喜温.软岩切削过程的三维数值模拟[J].长安大学学报(自然科学版),2010,30(04):102.
　XIA Yi-min,XUE Jing,ZHOU Xi-wen.3-D dimensional numerical simulation of soft rock cutting process[J].Journal of Chang’an University (Natural Science Edition),2010,30(03):102.
[10]顾海荣,焦生杰,肖翀宇,等.全液压路面铣刨机铣刨系统动力学仿真[J].长安大学学报(自然科学版),2010,30(05):103.
　GU Hai-rong,JIAO Sheng-jie,XIAO Chong-yu,et al.Dynamics simulation of milling system used in hydraulic milling machine[J].Journal of Chang’an University (Natural Science Edition),2010,30(03):103.

更新日期/Last Update: 2018-06-13