[1]张晨光,焦生杰,谢立扬,等.沥青搅拌设备烘干筒参数对骨料温升的影响[J].长安大学学报(自然科学版),2018,38(04):119-126.
　ZHANG Chen guang,JIAO Sheng jie,XIE Li yang,et al.Influence of rotary dryer parameters on aggregates temperaturerise in asphalt mixing plant[J].Journal of Chang’an University (Natural Science Edition),2018,38(04):119-126.
点击复制

沥青搅拌设备烘干筒参数对骨料温升的影响()
分享到：

长安大学学报（自然科学版）[ISSN:1006-6977/CN:61-1281/TN]

卷:
第38卷
期数:
2018年04期
页码:
119-126
栏目:
汽车与机械工程
出版日期:
2018-07-31

文章信息/Info

Title:
Influence of rotary dryer parameters on aggregates temperaturerise in asphalt mixing plant
作者:
张晨光; 焦生杰; 谢立扬; 翟资雄; 顾海荣
(1. 长安大学 道路施工技术与装备教育部重点实验室，陕西 西安 710064；2. 福建南方路面机械有限公司，福建 泉州 362021)
Author(s):
ZHANG Chenguang1;  JIAO Shengjie1;  XIE Liyang1;  ZHAI Zixiong2;  GU Hairong1
(1. Key Laboratory of Road Construction Technology and Equipment of Ministry of Education， ChanganUniversity， Xian 710064， Shaanxi， China； 2. Fujian South Highway Machinery Co. Ltd.，Quanzhou 362021， Fujian， China)
关键词:
机械工程; 沥青搅拌设备; 烘干筒; 参数优化; EDEMFLUENT耦合仿真; 传热模型
Keywords:
mechanical engineering;  asphalt mixing plant;  rotary dryer;  parameter optimization;  coupled EDEMFLUENT simulation;  heat transfer model
文献标志码:
A
摘要:
为了提高烘干筒的传热效率，以LB4000型沥青搅拌设备的烘干筒为研究对象，在分析烟气流体、固态骨料以及烘干筒壁之间辐射、对流、接触多种传热过程耦合作用的基础上，针对料帘区域建立了一维轴向传热模型，采用4阶RungeKutta算法分工况对模型进行了数值求解；分析叶片圆周数量和烘干筒转速对骨料温升的影响，采用基于EulerianEulerian算法的离散元流体力学耦合仿真（EDEMFLUENT）对烘干筒的传热过程进行了数值模拟，并对传热模型进行验证。研究结果表明：骨料进料率和料帘换热面积是影响骨料温升的主要因素，料帘特性对烘干筒传热效率有重要影响，平均每增加1 m2料帘换热面积，骨料的最终加热温度升高约1.3 ℃；叶片圆周数量由15片增加到20片，有利于增大料帘料量，加大换热面积，骨料最终加热温度明显升高，且骨料进料率越小温升幅度越大；提高烘干筒转速可增大料帘料量，但同时会缩短骨料在筒内的滞留时间，当烘干筒回转角速度为0.8 rad/s时，料帘换热效率与骨料在筒内滞留时间的匹配最佳，骨料最终加热温度最高，增大或减小烘干筒转速均会对骨料温升产生不利影响；在优化烘干筒结构参数，提高传热效率的同时，应避免因料帘与烟气换热过于充分而造成排烟温度过低，对后续的引风除尘系统带来不利影响。
Abstract:
To improve heat transfer efficiency of rotary dryer, based on the rotary dryer of LB4000 series asphalt mixing plant and the analysis of coupling effect of heat radiation, convection and contact transfer processes between flue fluid, solid aggregates and drum wall, onedimension axial heat transfer model was established for aggregates curtain area, the model was solved by the fourth order RungeKutta method to analyze the influence of the blade circumference and rotational speed of rotary dryer on aggregate temperature rise, based on the EDEMFLUENT. The results show that aggregates feed rate and heat transfer area of aggregates curtain are the main factors affecting the aggregates heating temperature，the characteristic of aggregates curtain has an important influence on the heat transfer efficiency of rotary dryer with an average increase of 1 m2 heat transfer area, the aggregates heating temperature is raised by about 1.3 ℃. The increase of blade circumference from 15 to 20 is beneficial to the increase the amount of aggregates curtain, the area of hear transfer, finale heating temperature of aggregates, and the smaller the aggregates feed rate, the higher the temperature rise increase rotational speed of rotary dryer can increase the amount of aggregates curtain, but also can shorten the residence time of them in the drum, and when the rotational speed is 0.8 rad·s-1, the heat transfer efficiency of aggregates curtain is matched perfectly with the residence time of aggregates, in the drum aggregates heating temperature is the highest, so that increasing or decreasing the rotational speed will both have an adverse effect on the aggregates temperature rise, while optimizing the rotary dryer parameters and improving the heat transfer efficiency, it should be avoided that heat transfer between aggregates curtain and gas is too full to cause the low exhaust gas temperature, which will lead to adverse effects on the following dustremoval system. 2 tabs, 8 figs, 26 refs.

相似文献/References:

[1]罗文军,罗天洪,甘信富,等.基于模糊-PI控制的沥青混凝土摊铺机行驶系统仿真[J].长安大学学报(自然科学版),2012,32(01):0.
[2]刘清涛,蔡宗琰,刘晓婷,等.面向工艺路线的废旧零部件可再制造性评价[J].长安大学学报(自然科学版),2012,32(03):105.
　LIU Qing-tao,CAI Zong-yan,LIU Xiao-ting,et al.Assessment on remanufacturability of waste parts for process route[J].Journal of Chang’an University (Natural Science Edition),2012,32(04):105.
[3]林 涛,刘 学,董忠红,等.大差速比平地机离合器接合过程[J].长安大学学报(自然科学版),2012,32(06):100.
　LIN Tao,LIU Xue,DONG Zhong-hong,et al.Engagement process of motor graders big differential speed ratio clutch[J].Journal of Chang’an University (Natural Science Edition),2012,32(04):100.
[4]刘 钊,焦生杰.工程机械用发动机动力性能评价指标[J].长安大学学报(自然科学版),2012,32(06):106.
　LIU Zhao,JIAO Sheng-jie.Evaluation criterion of engine power properties for construction machinery[J].Journal of Chang’an University (Natural Science Edition),2012,32(04):106.
[5]孟彩茹,李 磊,赵 真,等.沥青搅拌设备振动筛筛箱的动态特性分析[J].长安大学学报(自然科学版),2012,32(02):101.
　MENG Cai-ru,LI Lei,ZHAO Zhen,et al.Dynamic performance analysis of vibrating screen box in asphalt mixer[J].Journal of Chang’an University (Natural Science Edition),2012,32(04):101.
[6]侯劲汝,沈建军,徐 倩.双钢轮振动压路机振幅不均匀性的分析[J].长安大学学报(自然科学版),2010,30(01):100.
　HOU Jing-ru,SHEN Jian-jun,XU Qian.Analysis on uneven amplitude of tandem vibratory roller[J].Journal of Chang’an University (Natural Science Edition),2010,30(04):100.
[7]赵铁栓,焦生杰,叶 敏.振动压路机无级调幅H_2/H_∞控制[J].长安大学学报(自然科学版),2010,30(03):87.
　ZHAO Tie-shuan,JIAO Sheng-gjie,YE Min.H2/H∞ control for stepless amplitude modulation of vibratory roller[J].Journal of Chang’an University (Natural Science Edition),2010,30(04):87.
[8]焦生杰,卡玛尔,林 涛,等.H型液压滤波器的合理应用[J].长安大学学报(自然科学版),2010,30(04):97.
　JIAO Sheng-jie,KAMAL Washahi,LIN Tao,et al.Reasonable application on H type hydraulic filter[J].Journal of Chang’an University (Natural Science Edition),2010,30(04):97.
[9]夏毅敏,薛 静,周喜温.软岩切削过程的三维数值模拟[J].长安大学学报(自然科学版),2010,30(04):102.
　XIA Yi-min,XUE Jing,ZHOU Xi-wen.3-D dimensional numerical simulation of soft rock cutting process[J].Journal of Chang’an University (Natural Science Edition),2010,30(04):102.
[10]顾海荣,焦生杰,肖翀宇,等.全液压路面铣刨机铣刨系统动力学仿真[J].长安大学学报(自然科学版),2010,30(05):103.
　GU Hai-rong,JIAO Sheng-jie,XIAO Chong-yu,et al.Dynamics simulation of milling system used in hydraulic milling machine[J].Journal of Chang’an University (Natural Science Edition),2010,30(04):103.

更新日期/Last Update: 2018-08-03