[1]赵 秋,蔡文平,陈宝春.带平钢板剪力连接件的钢-RPC组合桥面板抗剪性能[J].长安大学学报(自然科学版),2017,37(02):64-72.
　ZHAO Qiu,CAI Wen-ping,CHEN Bao-chun.Shear performance of steel and RPC composite deck with smooth plate shear connector[J].Journal of Chang’an University (Natural Science Edition),2017,37(02):64-72.
点击复制

带平钢板剪力连接件的钢-RPC组合桥面板抗剪性能()
分享到：

长安大学学报（自然科学版）[ISSN:1006-6977/CN:61-1281/TN]

卷:
第37卷
期数:
2017年02期
页码:
64-72
栏目:
桥梁与隧道工程
出版日期:
2017-03-31

文章信息/Info

Title:
Shear performance of steel and RPC composite deck with smooth plate shear connector
作者:
赵 秋; 蔡文平; 陈宝春
福州大学 土木工程学院，福建 福州 350108
Author(s):
ZHAO Qiu;  CAI Wen-ping;  CHEN Bao-chun
College of Civil Engineering, Fuzhou University, Fuzhou 350108, Fujian, China
关键词:
桥梁工程; 组合桥面板; 抗剪性能; 活性粉末混凝土; 平钢板剪力键; 有限元
Keywords:
bridge engineering;  composite deck;  shear performance;  RPC;  smooth plate shear connector;  finite element
分类号:
U448.38
文献标志码:
A
摘要:
针对目前钢桥面铺装层因桥面横向刚度不足较易产生纵向裂缝的现象，提出一种能够提高桥面板横向刚度的平钢板抗剪连接件（以下称“平钢板剪力键”），该剪力键可使钢桥面板与活性粉末混凝土（reactive powder concrete, RPC）层连接在一起。为研究这种连接件组合桥面板中的抗剪传力机理，建立了组合桥面板推出试验的非线性有限元模型，并采用推出试验验证了该数值模型的破坏模式、抗剪承载力以及荷载-滑移曲线的正确性；结合有限元模型和试验结果，得到了平钢板剪力键推出试件的破坏模式；利用经试验验证的数值模拟方法分析了连接件板厚、活性粉末混凝土抗压强度、连接件屈服强度和有无钢筋网等参数对平钢板剪力键钢-RPC组合桥面板抗剪承载力的影响。研究结果表明：平钢板剪力键的破坏模式主要分为连接件根部被拉坏和剪力键下方RPC局部承压破坏2种；当RPC的抗压强度分别为80、100、120、140 MPa时，对应的平钢板剪力键的合理厚度分别为6、8、10、12 mm；随着平钢板剪力键材料强度的提高，组合桥面板抗剪承载力相应提高，且平钢板连接件厚度较小时提高幅度较明显，而厚度较大时提高不明显；随着RPC材料强度的提高，组合桥面板抗剪承载力相应提高，且连接件厚度较小时提高幅度较小；增设钢筋网对其承载力和刚度贡献不大，但可明显增大组合桥面板的抗剪延性。
Abstract:
In order to solve the problem that longitudinal cracks were commonly produced in the present normal deck surfacing layer of steel bridge due to its weak lateral stiffness, this paper put forward a kind of smooth plate shear connector that can improve the lateral stiffness of deck by making steel bridge deck and RPC layer work together. To study the shear force transfer mechanism of this kind of shear connector in composite deck, nonlinear finite element models (FEM) of composite deck of push out tests were established. The failure modes, shear bearing capacity and load-slip curves of numerical models were verified by tests. The failure modes of smooth plate shear connector’s push-out specimens were obtained by combining finite element models and test results. The verified numerical simulation method, the influence of several parameters, such as thickness and strength of connector, and compressive strength of RPC with steel fabric or not, on shear capacity of steel and RPC composite deck with smooth plate shear connector was analyzed. The results show that the failure modes of smooth plate shear connector can be classified into two types including tensile failure of connector root and local compression failure of RPC below the shear connector. When compressive strengths of RPC are 80, 100, 120, 140 MPa, the reasonable thicknesses of corresponding smooth plate shear connector are 6, 8, 10, 12 mm respectively. The shear bearing capacity of composite bridge deck correspondingly increases with the increase of strength of smooth plate shear connector material and the increase range of thin steel plate connector is more significant than that in thick one. The shear bearing capacity of composite bridge deck also correspondingly increases with the increase of strength of RPC, while the increase range is not obvious when the thickness of steel plate connector is relatively small. Contribution of increasing steel fabric to bearing capacity and stiffness of composite deck is little, but it is extremely useful for improving shearing ductility of composite bridge deck.

相似文献/References:

[1]李宇,朱晞,杨庆山,等.高墩大跨桥梁结构的脆弱性分析[J].长安大学学报(自然科学版),2012,32(01):0.
[2]高亮,刘健新,张丹,等.桁架桥主梁三分力系数试验[J].长安大学学报(自然科学版),2012,32(01):0.
[3]刘旭政,王丰平,黄平明,等.斜拉桥各构件校验系数的常值范围[J].长安大学学报(自然科学版),2012,32(01):0.
[4]尚维波,张春宁.高墩刚构桥系梁抗震分析[J].长安大学学报(自然科学版),2012,32(01):0.
[5]邬晓光,李冀弘,宋伟伟.基于改进响应面法的在役PC桥梁承载力可靠性[J].长安大学学报(自然科学版),2012,32(03):53.
　WU Xiao-guang,LI Ji-hong,SONG Wei-wei.Reliability of existing PC bridge based on improved response surface method[J].Journal of Chang’an University (Natural Science Edition),2012,32(02):53.
[6]石雄伟,袁卓亚,马毓泉,等.钢板-混凝土组合加固预应力混凝土箱梁[J].长安大学学报(自然科学版),2012,32(03):58.
　SHI Xiong-wei,YUAN Zhuo-ya,MA Yu-quan,et al.Prestressed concrete box girder strengthened with comsposition of steel plate and concrete[J].Journal of Chang’an University (Natural Science Edition),2012,32(02):58.
[7]李传习,陶 伟,董创文.斜交墩截面刚度与弯曲正应力[J].长安大学学报(自然科学版),2012,32(03):63.
　LI Chuan-xi,TAO Wei,DONG Chuang-wen.Sectional stiffness and bending normal stress of oblique pier[J].Journal of Chang’an University (Natural Science Edition),2012,32(02):63.
[8]邓继华,邵旭东.带铰平面梁元几何非线性有限元分析[J].长安大学学报(自然科学版),2012,32(03):68.
　DENG Ji-hua,SHAO Xu-dong.Geometric nonlinear finite element analysis of plane beam element with hinge[J].Journal of Chang’an University (Natural Science Edition),2012,32(02):68.
[9]蒲广宁,赵 煜,宋一凡.减梁增肋法加固空心板桥的力学性能[J].长安大学学报(自然科学版),2012,32(06):38.
　PU Guang-ning,ZHAO Yu,SONG Yi-fan.Mechanical properties of strengthening hollow slab bridge based on beam-reduction and rib-addition method[J].Journal of Chang’an University (Natural Science Edition),2012,32(02):38.
[10]党 栋,贺拴海,周勇军,等.基于车辆统计数据的汽车荷载标准值取值与评估[J].长安大学学报(自然科学版),2012,32(06):44.
　DANG Dong,HE Shuan-hai,ZHOU Yong-jun,et al.Choosing and assessment for the standard of vehicle load based on vehicle statistical data[J].Journal of Chang’an University (Natural Science Edition),2012,32(02):44.

更新日期/Last Update: 2017-04-07